BENEFITS: BIOCHEM - 80 controls slime-forming bacteria, sulfate-reducing bacteria and algae in air washers, re-circulating cooling and process water systems, including pasteurizers and warmers and once-through cooling water systems, retort water systems and industrial, re-circulating process water systems.

DESCRIPTION: BIOCHEM - 80 is a US EPA-registered micro-biocide containing 45%glutaraldehyde. It is a liquid product for use in controlling slime-forming bacteria, sulfate-reducing bacteria and algae.

PRODUCT DOSAGE: Badly fouled air washers and re-circulating cooling water systems should be cleaned before treatment. BIOCHEM - 80 can be used on an intermittent (slug dose) schedule or a continuous-feed schedule. For specifice dosage information on evaporative condensers, hydrostatic sterilizers and retorts, pasteurizers and warmers, consult the EPA-registered product label.

METHOD OF FEED: Feed the product directly from the container into the tower basin, distribution deck or re-circulating line. When feeding into the re-circulating line, use a high-volume electronic metering pump and time clock.

SYSTEM OPERATING PARAMETERS: Follow the same parameters as outlined for cooling tower treatments.

PRODUCT CONTROL PARAMETERS: BIOCHEM - 80 is effective in cooling water systems having a pH range of 6 to 9. Systems operating above a pH of 9, or with 25-50 ppm ammonia present, please contact AB SOLUTIONS Representatives will recommend dosage.

PHYSICAL PROPERTIES:
Appearance: Clear
Specific Gravity: 1.12
Density: 9.34 lb / gallon

COOLCHEM-100
COOLING TOWER DISPERSANT AND
ON-LINE DESCALER

COOLCHEM-100 is not effective on silica scale. Scale thicker than 1/4 inch should be decaled with an acid type product. COOLCHEM-100works with the system over a period of months by sequestering deposits and scale. On-line descaling may take six months or longer for scale removal.

PRODUCT DOSAGE: For on-line descaling, add 1 gallon of COOLCHEM-100 per 2,000 gallons cooling tower capacity. Maintain dosage based on bleed off. Product dosage may vary up to 1 gallon per 700 gallons of bleed off.

WHEN USED AS A DISPERSANT: COOLCHEM-100 is a liquid blend of sodium polymer. It is effective in all cooling towers, especially systems that collect silt and airborne debris. The high-molecular-weight polymer lifts and suspends mud, silt and iron oxide and allows their removal through normal bleed off.

PRODUCT DOSAGE: When used as a cooling tower dispersant, add 1 gallon of COOLCHEM-100 for each 6,000 gallons of water in the system. Add 1 gallon for each 6,000 to 12,000 gallons of water lost to bleed off.

METHOD OF FEED: Feed COOLCHEM-100 directly into the cooling tower sump or into the return line to the tower.

SYSTEM OPERATING PARAMETERS: Follow the same parameters as outlined for phosphonate treatment programs.

PRODUCT CONTROL PARAMETERS: Treatment residuals for COOLCHEM-100 cannot be tested conveniently. Feed this product in proportion the  phosphonate treatment and use phosphonate residual as the control parameter.

PHYSICAL PROPERTIES:
Appearance: Colorless liquid
Product pH: 11.5
Specific Gravity (73 F): 1.06
Density: 8.84 1bs/gal

WARNING: Concentrated product is a severe eye and skin irritant
Read the full product label for all use directions and precautions.

BD -120 (BIO DISPERSENT)

DESCRIPTION: BIO DISPERSENT is a surfactant and penetrates for dispersing microbiological slimes and oil-type deposits in cooling tower systems.

Slimes and oil-type deposits impede water flow, restrict heat transfer and cause metal components to corrode.

BIO DISPERSENT breaks up the entire slime mass. It reacts with the biomass by breaking its slime coating into thousands of tiny pieces. This destroys its natural defense mechanism and leaves the slime defenseless.

Biocides are now able to attack the entire biomass and kill the dispersed microbiological agents. Following the application of the biocide, the surface is free of bacteria.

APPLICATION: For initial treatment or severely contaminated systems, add 1 gallon of BIO DISPERSENT for each 5,000 gallons of water. A dosage of 1 gallon of BIO DISPERSENT for each 50,000 gallons of water should be maintained in order to provide adequate protection.

CHILLCHEM-100
CLOSED-LOOP CORROSION INHIBITOR

DESCRIPTION: CHILL CHEM-100 is a liquid blend of sodium nitrite, sodium borate, yellow metal inhibitor and a dispersant. CHILL CHEM-100 is a non-chormate inhibitor, specially formulated for corrosion protection in copper, steel and multi-metal systems, whether they are airtight or not.

APPLICATION: CHILL CHEM-100 is a corrosion inhibitor for use in chilled-water closed loops, hot-water re-circulating boilers, and above-ground thermal storage systems. This product provides effective corrosion protection for metals typically found in closed-loop systems. In addition, CHILL CHEM-100 contains a borate buffer to maintain the pH of the re-circulating water in the range of 8.5 to 10.5.

PRODUCT DOSAGE: The initial dosage of CHILL CHEM-100 is 1 liter for each 1000 liters of water in the system (1100 ppm). This will provide a sodium nitrite residual of 275 ppm as NaNo2. The maintenance dosage is 1 gallon of CHILL CHEM-100 for each 1000 gallons of make-up water added to the system. The sodium nitrite level should be aintained in the range of 250 ppm to 400 ppm. The pH of the re-circulating water should be in the range of 8.5 to 10.5. Do not allow the pH to drop below 8.0.

METHOD OF FEED: Feed CHILL CHEM-100 to the closed-loop system using a by-pass pot feeder. For above-ground thermal storage systems, add the product at the time the system is initially charged with water.

SYSTEM OPERATING PARAMETERS:
Re-circulating water pH:8.5 to 10.8
Maximum water temperature: 350 F

PRODUCT CONTROL PARAMETERS:
Nitrite as NaNO 225 to 400 ppm
Recirculating water conductivity: 3500 umho or less
Recirculating water pH:8.5 to 10.5

PHYSICAL PROPERTIES:
Appearance: Colorless liquid
Product pH:10.8
Specific gravity (73 F): 1.10
Density: 1.10 kg/L

NOTE: Not for use in or for contact with potable water systems or domestic water sources. Not for use in electric steam boilers.

KEEP FROM FREEZING. If this product is stored in cold or freezing temperatures, it may separate or thicken. This will not harm the performance. Before using, warm to room temperature and stir thoroughly.

WARNING
CAUSES SKIN IRRITATION AND ALLERGIC SKIN REACTION
CAUSES SEVERE EYE IRRITATION
MAY CAUSE IRRITATION IF INHALED

HARMFUL IF SWALLOWED
Contains Sodium Met silicate and Sodium Nitrite. Avoid contact with skin, eyes and clothing. Wear neoprene rubber gloves, goggles and protective clothing when handling. Wash thoroughly after handling. Avoid breathing the mist. Use sufficient ventilation to prevent the buildup of mist. Do not swallow. Swallowing may cause nausea, diarrhea or vomiting.

FIRST AID
FOR SKIN CONTACT: Wash affected areas with large amounts of soap and water for 15minutes. Remove contaminated clothing and shoes. Get immediate medical attention. Wash clothing and clean shoes before reuse. FOR EYE CONTACT: Immediately rinse the eyes with water. Remove any contact lenses and continue flushing for at least 15 minutes. Hold the eyelids apart to ensure rinsing of the entire surface of the eyes and lids with water. Get immediate medical attention. IF INHALED: Remove from the area to fresh air. Seek medical attention if respiratory irritation develops or if breathing becomes difficult. IF SWALLOWED: Immediately give 3 to 4 glasses of water and induce vomiting by placing a finger or blunt object on the back of the victim’s tongue. Give fluids until the vomits is clear. Get immediate medical attention. Do not induce vomiting or give anything by mouth to an unconscious or convulsing person.

KEEP OUT OF REACH OF CHILDREN

BIO CHEM - 30
Liquid Oxidizing Activator

Specifically Designed For Use with BIOCHEM 80 Biocide

METHOD OF FEED: The delivery system must provide thorough mixing of BIOCHEM 80 and BIO CHEM - 30. BIOCHEM 80 should be added to the circulation water just before the BIO CHEM - 30

PHYSICAL PROPERTIES:
Colour : Light yellow green
Product pH : 12.4
Specific gravity : 1.18
Density : 19.2
Odor : Chlorine

BIO CHEM – 80

Controls Bacteria, Fungi, Algae and Slime

DESCRIPTION: BIO CHEM - 50 is a liquid, oxidizing biocide specially formulated to control bacteria, algae, fungi and slime in recirculating and once-through cooling water systems, breweries, pasteurizing systems, waste water systems and pulp and paper mills. The EPA registration number is 3377-25-64488. A bromine-based biocide, BIO CHEM - 80 was developed to overcome the deficiencies of chlorine and chlorine derivatives. It must be used in conjunction with an oxidizing catalyst such as Biochem 30.

DOSAGE RATES: Initial Dose: When the system is noticeably fouled, apply sufficient BIO CHEM - 80 and BIOCHEM30 to achieve a residual bromine level of 0.5-1 ppm or as needed to maintain control. Typically, the recommended rate is 1.3-5.2gallon Biochem30 for each gallon of BIO CHEM - 80.

METHOD OF FEED: BIO CHEM - 80 may be added to the system either continuously or intermittently or as needed, but should be added to the circulation water just before the BIOCHEM30. The frequency of feeding and duration of the treatment will depend upon the severity of the problem. It is recommended that the product be used in a manner such that the effluent discharges meet the NPDES guidelines.

PHYSICAL PROPERTIES:
Appearance: Clear liquid
Product pH (1:10 dilution): 7.0-9.0
Specific gravity (70 F): 1.385-1.440
Density: 11.6-12.1
Hardness as CaCo3 maximum: 55 ppm
Flashpoint: None

ANTI-FOAM
ANTI-FOAM CHEMICAL AGENT

DESCRIPTION:
ANTI-FOAM is a silicone-based anti-foam agent formulated to reduce and kill foam in cooling tower descaling operations.

METHOD OF APPLICATION For best result, dilute ANTI FOAM with 5 to 10 parts water and spray directly on the foam blanket.

CAUTION
MAY CAUSE EYE IRRITATION
Avoid contact with eyes. Wear safety glasses if the method of application presents the likelihood of eye contact. Wash thoroughly after handling.

FIRST AID
FOR EYE CONTACT: Rinse the eyes with water. Remove any contact lenses and continue flushing with plenty of water for several minutes. Seek medical attention if irritation develops.

KEEP OUT OF REACH OF CHILDREN
See the Material Safety Data Sheet for more information.
get medical or environmental emergencies, .

COOLCHEM-105
COOLING TOWER TREATMENT FOR HIGH-SILICIA WATER

BENEFITS: COOLCHEM-105 is specially formulated to inhibit the deposition of silica scale in cooling systems where the silica content of the feed water is over 25 ppm.

DESCRIPTION: COOLCHEM-105 is a primary scale and corrosion inhibitor. It is a liquid blend of phosphonic acid, polymers and a yellow metal corrosion inhibitor.

APPLICATIONS: Use COOLCHEM-105 whenever the cooling tower feed water contains 250 or more ppm of silica. The initial dosage in the cooling water is 1 gallon of product for each 2000 gallons of system capacity. Continue the dosage for 7 days. The maintenance dosage is 1 gallon of product for each 6,000 gallons of bleed off to maintain 10-20 ppm phosphonate in the system.

PRODUCT DOSAGE: Use COOLCHEM-105in cooling tower systems when the total ppm of silica in the tower water would exceed 150 ppm. The initial dosage in the cooling water is 1 gallon of product for each 2000 gallons of system capacity. Maintain this initial concentration (30 ppm phosphonate) for 7 days. The maintenance dosage is 1 gallon of product for each 6000 gallons of bleed off to maintain 1-20 ppm phosphonate in the system.

METHOD OF FEED: COOLCHEM-105 can be fed directly into the cooling tower sump, or directly into the re-circulating waterline, with the midstream injection tip. This product should not be mixed with biocides in chemical feed solutions.

SYSTEM OPERATING PARAMETERS:
Total hardness  700 ppm maximum
Total alkalinity: 500 ppm maximum
Silica (theoretical): 300 ppm maximum
Conductivity: 3500 micromhos maximum   

PRODUCT CONTROL PARAMETERS:
Phosphonate: 10 to 20 ppm as PO2

PHYSICAL PROPERTIES:
Appearance; Pale yellow
Pft: 1.6
Specific Gravity: 1.0769
Density: 8.98 lbs/gallon

DANGER
CAUSES SKIN AND EYE BURNS
CAUSES IRRITATION IF INHALED
HARMFUL IF SWALLOWED

Contains Aminotri (Methylenephosphonic Acid) Do not get in eyes, on skin, or clothing. Wear a face shield, neoprene rubber gloves and protective clothing when handling. Wash thoroughly after handling. Keep the container closed when not in use. Avoid breathing the mist.. Use sufficient ventilation to prevent a buildup of mist. Do not swallow.

FIRST AID
FOR SKIN CONTACT: Wash affected areas with large amounts of running water, and soap if available for 15 minutes. Remove contaminated clothing and shoes. Get immediate medical attention. Wash clothing and decontaminate shoes before reuse.

FOR EYE CONTACT: Immediately rinse the eyes with water. Remove any contact lens Hold the eyelids apart to ensure rinsing of the entire surface of the eyes and lids with water. Continue fleshing with large amount of running water for atleast 15 minutes. If a physician is not available, flesh for an additional 15 minutes. Get immediate medical attention.

IF INHALED: Remove from the area to fresh air. Seek medical attention if respiratory imitation develops or if breathing becomes difficult. IF SWALLOWED: Give 3 to 4 glasses of water but DO NOT induce vomiting. If vomiting occurs, give fluids again. Have a physician determine if the patient’s condition allows induction of vomiting or evacuation of the stomach. Do not give anything by mouth to an unconscious or convulsing person. Get immediate medical attention.

KEEP OUT OF REACH OF CHILDREN
See the Material Safety Data Sheet for more information.

SUGAR GRADE FLOCCULANT
Superfloc A 110 PWG SG

SUPERFLOC Sugar Grade flocculants are high molecular weight anionic polyacrylamides developed specifically for the clarification of sugar juice.

HANDLING
Animal tests have shown that SUPERFLOC Sugar Grade flocculants can be considered to be practically non-toxic; they should offer no hazard to health under reasonable conditions of industrial handling and use. Spilled polymer is very slippery. Spills should be scooped and / or wiped up prior to flushing with water.

SUPERFLOC C-573 (Coagulant)

APPLICATION

Superfloc C-573 can be prepared as a 1% solution in water and dosed in the process line or in a flash mixer tank. It is very easily soluble in water. Jar studies should be conducted to optimise the dose. It should be added just before the flocculant is added to the cane juice.

TYPICAL PROPERTIES:

Appearance                  :           Amber Liquid
Charge                         :           Cationic
Relative Mol.Wt            :           Low
Specific Gravity at 25 C :           1.14 - 1.18
Freez Point                   :           -18 C
Shelf Life (Stored 38 C) :           2 years
Polymer Content           :           49 - 51%

HANDLING
Animal tests have shown that SUPERFLOC Sugar Grade flocculants can be considered to be practically non-toxic; they should offer no hazard to health under reasonable conditions of industrial handling and use. Spilled polymer is very slippery. Spills should be scooped and/or wiped up prior to flushing with water.

Trade Mark Notice: The indicates a Registered Trademark

SUPERFLOC FLOCCULANTS
Dry Polyacrylamide (PAM), cationic: C 492 HMW

The C- 492 of very high molecular weight SUPERLOC cationic flocculants of different molecular weight and charges effective condition solids for dewatering operations and aid water clarification processes in a wide variety of industries. The chemistry range available ensures there is product suitable for each individual application.

Principal Uses

SUPERLOC  dry PAM cationic flocculants are recommended for the following liquid-solid
Separation processes,

The above are the primary applications for these products. These products may be beneficial in any liquid- solid separation process.

Application:
Stock solutions can be prepared up to 0.5% concentration via an automated make down unit or on a batch basis. Solutions should be aged 30-60 minutes for maximum effectiveness. High quality make up water should be used. Secondary dilution water should be added to the stock solution prior to the addition point at a ratio of at least 10:1 Centrifugal pumps should be avoided for polymer transfer

Health and Safety
These products can irritate the eyes and skin. Rubber gloves, goggles and protective clothing are recommended for use while handling. They are not acutely toxic by oral and dermal administration to laboratory animals thought eye irritation did result. See the Material Safety Data Sheet for complete safety, health and environmental data.

Handling and storage

Solutions are no more corrosive than water and recommended materials of construction include stainless steel, fiber glass, plastic and glass or epoxy lined vessels. Do not use iron, copper or aluminium. Spilled polymer is very slippery and should be collected prior to flushing with water. The Shelf life of these products is 12 months when stored in unopened packages in a dry atmosphere at temperature no higher than 40 C

abs - bw 147

abs – bw 147 is a liquid chemicals formulations designed for feed water treatment of coil type boilers. It contain a powerful anti-scalent along with a catalyzed oxygen scavenger. It reduce oxygen corrosion and depositions of calcium and iron compounds in the coils. Without contributing much to the dissolved solids.

Applicvations: To be mixed with feed water in the feed water tank or at the inlet of the feed water pump.

TYPICAL PHYSICAL PROPERTIES:

pH (Neat)                   : 9.5 – 10.00
Spec. gravity              : 1.05 – 1.07
Miscibility                    : Completely miscible
Colour                         : Colorless

DOSAGE:
Depends on feed water quality / quantity. Follow AB Solutions service personal recommendations

PACKING:25kg/50kgs carbouys.

Handling and storage:
The product is safe for use in boilers. It can be stored in the boiler house. Please wear protective gloves and goggles while handling the product. Wash with excess water whenever it contacts the skin

ABS – 100S
ANTISCALANT FOR SUGAR MILLS

pRODUCT DESCRIPTION   ABS- 100S is an antiscalant specifically designed for the                                                            control of scale formation in sugarcane juice evaporators.

                                          ABS – 100S can be directly added to the clarified juice                                                             before it enters the evaporators.

SPECIFICATION                   Appearance            : Clear colours to yellow liquid
                                                pH (as                : 4.0 to 7.0           
                                                Wt. /ml                : 1.0 – 1.2

ABS – 100S exhibits excellent control of scaling due to calcium carbonates, calcium sulphate, calcium phosphate, calcium oxalate and silica which are normally encountered in juice evaporators. Substoichiometirc concentrations of ABS – 100S prevents the precipitation of scale forming salts by its threshold inhibition property.

ABS – 100S is a powerful sequestrate of cations. It forms water soluble complexes with scale forming ions like calcium, magnesium, etc.

ABS – 100S effective controls the depositions of suspended matter like dirt, dust, etc. By its strong dispersing ability. ABS- 100S is hydrolytically very stable over a wide rang of pH and temperature

The scales, if any, formed with the use of ABS – 100S are amorphous in nature due to distortion of their crystal structure and can be easily removed. ABS 100S does not interfere with the sugar crystallization process.

ADVANTAGES

DOSAGE: 

ABS-100S should be dosed at a concentration at 10 – 20 ppm on the basis of clarified juice.

FEEDINGS

ABS-100S should be diluted to 5 – 100 times with water and mixed with the clarified juice at a point just before its entry into the evaporators.  In most cases, split feeding has been found to be more effective.

PACKING

ABS 100S in concentrated form is irritating to skin.  Avoid contact with eyes and skin . Wash with plenty of water in case of contract. Do not take internally.